
Paver installation
Interlocking paver surfaces for patios, drives, paths and pool decks, built on a base sized for the job it has to carry.

A walkway is a narrow surface with two long edges, and those edges are where most paths fail. We build paver walkways on a compacted base with a fixed restraint along both sides, so the lines you see on day one are still there years later.
On a patio, each paver is surrounded by others. On a walkway, the pavers along each edge have nothing on one side but gravel, soil or a planting bed. Without a solid restraint, foot traffic and irrigation slowly push those outer rows outward, the joints open, and the straight edge turns wavy.
So our paver walkway installation starts with a base that runs a little wider than the finished path, compacted in layers, with the edge restraint staked into it on both sides. We give the walkway a slight cross slope so water from a summer storm runs off into the landscape instead of sitting on the surface or creeping toward the house.
The route from the drive or sidewalk to the front door, sized for two people walking side by side and often tied into the driveway in a matching paver or border.
Paver paths down the side of the house to the back yard, the trash bins or the pool equipment, replacing loose gravel that tracks indoors and shifts underfoot.
Curved or straight paths through desert planting that link a patio to a gate, a seating area or another part of the yard.
Marking the route on the ground, then clearing out old concrete, pavers, gravel or turf along it.
Digging to firm soil, compacting the subgrade, and building a compacted aggregate base wider than the path itself.
Setting the walkway pavers in your chosen pattern, with curves and border pieces cut on a wet saw for clean lines.
Fixing restraint on both sides, sweeping sand into the joints and compacting the surface so the pavers lock together.
We walk the route with you and note slopes, steps, sprinkler lines and where water crosses the path.
We settle the width, shape, paver and border, and how the walkway meets your door, drive or patio.
A clear scope listing removal, base, pavers and edging so you can compare it with other bids.
We call in utility locates before any digging, since walkways often run over service lines.
Removal, excavation, base, bedding, laying, restraint, sand and compaction.
We walk the finished path with you and leave spare pavers for future repairs where we can.
We treat a walkway as real paving, not a leftover strip at the end of a bigger job. It gets the same compacted base and the same edge detail as a patio.
We also look at what surrounds the path. Irrigation, gravel and planting beds all push on a walkway edge, so we plan the restraint and the finished height around them.
Tell us where the walkway needs to go and what is there now, and we will come out to walk the route with you.
Compacted native soil, then a layer of crushed aggregate base compacted in lifts, then a thin screeded layer of coarse bedding sand. On soft or mixed soil we add a geotextile fabric under the base.
The main drivers are length and width, what has to be removed first, how many curves and cuts the design needs, the paver you choose, and whether steps or grade changes are involved. We measure the route at a free on-site visit and send a written estimate.
Not if you want straight edges. A walkway has open soil or planting on both sides, and irrigation keeps that ground damp, so pavers set on bare dirt sink along the edges first and the rows start to drift. We dig to firm soil and build a compacted base wider than the path so the restraint has something solid to stake into.
Without a compacted gravel base, the pavers rest on soil or sand alone. Water softens that layer, foot traffic presses it unevenly, and the path develops dips, rocking pavers and open joints.
It depends on the soil and on what crosses the path. A garden path that only sees foot traffic needs less than a front walk that carries trash bins and wheelbarrows, and soft or clay heavy ground needs more again. We set the depth after seeing your soil, run the base a little wider than the path, and write the depth on the estimate.
We build paver walkways and paths across Tucson and the surrounding communities, including Oro Valley, Marana, Catalina Foothills, Casas Adobes, Vail, Sahuarita, Green Valley, Rita Ranch and Tanque Verde.

Interlocking paver surfaces for patios, drives, paths and pool decks, built on a base sized for the job it has to carry.

Driveways built to a vehicle load base, laid in a pattern that locks under turning tires and lifts out cleanly for repairs.

Interlocking paver patios with a compacted base, a restrained edge and a steady fall away from the house.
Tell us roughly how long the path is, where it runs and what is there now. We will come out, walk the route and send a written estimate.
We will be in touch to set a time to visit. If it is urgent, call (520) 555-0153.